ISO 10555-5 PDF

The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to. à aiguille interne. STANDARD. ISO. Second edition. Reference number. ISO (E). Provläsningsexemplar / Preview. STANDARD. ISO. Second edition. Reference number. ISO (E). This is a free 4 page sample. Access the full version online.

Author: Mikajind Zulura
Country: Papua New Guinea
Language: English (Spanish)
Genre: Software
Published (Last): 2 February 2013
Pages: 109
PDF File Size: 6.15 Mb
ePub File Size: 6.5 Mb
ISBN: 615-7-74498-881-6
Downloads: 98066
Price: Free* [*Free Regsitration Required]
Uploader: Nahn

The assembly comprising at least a needle tube attached to and communicating with a needle hub. Standards are also reviewed periodically; a standard alongwith amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision.

E-5 Isso report The test report shall contain at least the following information: The fluid is allowed to flow into the needle, and the time taken for fluid to leak through the vent fitting is measured.

Intravascular catheters ISO , -3, -4, -5

Blood flow into the needle hub. Bureau of Indian Standards BIS is a statutory institution established under the Bureau of Indian Standards Act, to promote harmonious development of the activities of standardization, marking and 1055-5 certification of goods and attending to connected matters in the country. Fitting attached to the needle tube, providing communication with its bore.

If a steel tube is used, it shall connply with ISO I Principle Water is allowed to flow through the catheter and the amount of flow is measured either volumetrically uso gravimetrically. An example of a suitable apparatus is shown in fig- ure B.

In this adopted standard, reference appears to certain International Standards for which Indian Standards also exist. The details of conditions under which the licence for the use of the Standard Mark may be granted to manufacturers or producers may be obtained from the Bureau of Indian Standards.

  DATASHEET CD4049 PDF

Designation and catalogue of CCR colours. No part of the these publications may be reproduced in any form without the prior permission in writing of BIS. At the time of publication, the editions indicated were valid. The corresponding Indian Standards which are to be substituted in their places are listed below along with their degree of equivalence for the editions indicated: Details of which is given in National Annex A.

Available from Munsell Color, N. The fluid pathway in the needle shall be free of unintended obstructions that would prevent flashback.

ISO 10555-5:1996

For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated expressing the result of is test or analysis, shall be rounded off in accordance with IS 2: The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard.

Part 1 General requirements do The technical committee has reviewed the provisions of the following International Standard referred in this adopted standard and has decided that it is acceptable for use in conjunction with this standard: Rigid tube with one end sharpened to facilitate entry into body tissue. When tested in accordance with annex E, fluid shall not leak out of the vent fitting within 15 s.

Other parts of this standard are as follows: Until that time, sio manufacturer may label his product “radio- opaque” provided he can support this claim by demonstrat- ing that he has an appropriate method for showing radio- opacity.

This Indian Standard has been developed from Doc No.: Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of ‘BIS Catalogue’ and ixo When the needle is fully inserted into the catheter unit, the catheter tube shall neither extend beyond the heel of the needle bevel nor be nnore than 1 nnnn fronn it see dinnension a in figure 1.

  BIRKHOFF ALGEBRA MODERNA PDF

NOTE 3 The point should be designed to be noncoring.

BS EN ISO 10555-5:2013

Attention is particularly drawn to the following: This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations.

The catheter tube may have a single lumen or multiple lumens. Limited collection of colours. I Principle A force is applied successively tensile and connpress- ive to the needle tube and needle hub and the tube- hub union is then examined for loosening. Copyright BIS has the copyright of all its publications.

Review of Indian Standards Amendments are issued to standards as the need arises on the basis of comments.

International Standard ISO Catheter designed for the introduction or withdrawal of liquids or devices into or from the peripheral vascular system. Figure 1 — Typical over-needle peripheral intravascular catheter NOTE 2 At the time of publication of this part of ISOthere is no acceptable, validated test method 10555–5 determine radio-detectability.

Measure the time taken for fluid to form the first falling drop at the back of the vent fitting. Certain conventions are, however, not identical to those used in Indian Standards. NOTE To improve the visibility of the solution, a colorant 1055-5 as red or blue food dye may be incorporated.

Round the calculated average water fiowrate to the nearest whole number of millilitres.