ICL, ICL Datasheet, ICL 3 1/2 Digit LCD Display, buy ICL The Maxim ICL and ICL are monolithic analog . descriptive excerpts from the original manufacturer’s data sheet have been included in this data. ICL datasheet, ICL circuit, ICL data sheet: INTERSIL – 3 1/2 Digit, LCD/LED Display, A/D Converters,alldatasheet, datasheet, Datasheet search.

Author: Shasho Shatilar
Country: Zimbabwe
Language: English (Spanish)
Genre: Politics
Published (Last): 22 August 2006
Pages: 260
PDF File Size: 13.72 Mb
ePub File Size: 17.42 Mb
ISBN: 577-6-31193-602-7
Downloads: 4770
Price: Free* [*Free Regsitration Required]
Uploader: Shakataxe

ICL is tested in the circuit of Figure 2. Figure 10 shows this application. In the lamp test mode, the segments dataheet a constant DC voltage no square-wave. Average DC component is less than 50mV.

This difference in reference for positive or negative input voltage will give a roll-over error. It is identical to the ICL except that the regulated supply and back plane drive have been eliminated and the segment drive has been increased from 2mA to 8mA, typical for instrument size common anode LED displays. In either case, an external reference can easily be added, as shown in Figure 4.

Thus, it can be used as the negative supply for externally generated segment drivers such as decimal points or any other presentation the user may want to include on the LCD display.

ICL Datasheet(PDF) – Intersil Corporation

In all cases negligible DC voltage exists across the segments. Do not operate at or near the maximum ratings listed for extended periods of time. This makes the system slightly quieter and also avoids a divider network on the input.


Integrating Capacitor The integrating capacitor should be selected to give the maximum voltage swing that ensures tolerance buildup will not saturate the integrator swing approximately. N is the maximum number of terminal positions. The oscillator frequency is divided by four before it clocks the decade counters.

ICL, ICL, ICLS Datasheet

Auto-Zero Capacitor The size of the auto-zero capacitor has some influence on the noise of the system. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www. This supply is made stiff to absorb the relatively large capacitive currents when the back plane BP voltage is switched.

Direct drive with digital logic supply amplitude.

Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Limit is not production tested.

D, D1, and E1 dimensions do not include mold flash or protrusions. Page 4, Reworded Electrical Spec Note 9 formerly note 5 from: Devices with a positive TC reference may require several counts to pull out of an over-range condition. In case of conflict between English and Metric dimensions, the inch dimensions control.

For these critical applications the integrator output swing can be reduced to less than jcl7106 recommended 2V full scale swing with little loss of accuracy. A worst case condition would be a large positive common mode voltage with a near full scale negative differential input voltage. Dimensions D and E to be determined at seating plane -C. However, where a large common mode voltage exists i. Input low is internally connected to analog COMMON and input high is connected across the previously charged reference capacitor.


On the 2V scale, a 0. Please refer to TB for details on reel specifications.

Datasheets search archive of electronic components datasheets

Reliability reports are also available from datasheeh website at www. True differential inputs and reference are useful in all systems, but give the designer an uncommon advantage when measuring load cells, strain gauges and other bridge type transducers.

E and eA are measured with the leads constrained to be perpendicular to datum -C. The integrating resistor should be large enough to remain in this very linear region over the input voltage range, but small enough that undue leakage requirements are not placed on the PC board. Information furnished by Intersil is believed to be accurate and reliable. For mV full scale where noise is very important, a 0.

An R-C oscillator using all three pins. If reference can be conveniently tied to analog COMMON, it should be since this removes the common mode voltage from the reference system. Submit Document Feedback 16 FN Since icl77106 comparator is included in the loop, the A-Z accuracy is limited only by the noise of the system.