HT12E ENCODER DATASHEET PDF

HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. Fri, 12 Oct GMT ht12e encoder ic ht12e datasheet pdf – HT12E is an encoder integrated circuit of. 2 12 series of encoders. They are. HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the.

Author: Kajikinos Tebar
Country: Monaco
Language: English (Spanish)
Genre: Love
Published (Last): 13 June 2018
Pages: 323
PDF File Size: 10.24 Mb
ePub File Size: 19.89 Mb
ISBN: 944-9-18131-992-4
Downloads: 1891
Price: Free* [*Free Regsitration Required]
Uploader: Meztill

Connected to the Ground of circuit. This cycle is repeated as long as TE is kept low. Choosing Battery for Robots. Interface SD Card with Arduino. Arduino based GPS receiver. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. HT12E has a transmission enable pin which is active low. These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits.

HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet

They are paired with 2 12 series of decoders for use in remote control system applications. Vatasheet be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. SPI Module of Arduino.

  HETTICH EBA 21 USER MANUAL FILETYPE PDF

Can range from 2. These two ICs together form an Encoder and Decoder pair. TL — Programmable Reference Voltage.

Virgin Galactic — Commercial Space Flight. Pull the Transmission Enable pin pin 14 to ground to activate transmission. HT12E is an encoder integrated circuit of 2 12 series of encoders.

This oscillator can be used by connecting these two pins through a 1M Resistor. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. These are the 8-bit address bits, which is used to protect your data.

HT12E Datasheet

The primary function of HT12E is to encode a bit and send it out through the output dncoder. The IC is has a wide range of operating voltage from 2. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side daatasheet HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC.

The encoded bit can be obtained from the Dout pin pin Submitted by admin on 30 October Transmission enable; active low. These 12 bits are divided into 8 address bits and 4 data bits. The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. If you want security you can connect any of the 8 pins to 5V to make it high. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

  CUERPO POETICO JACQUES LECOQ PDF

Choosing Motor For Robots.

The Encoded 12 bit output data can be obtained from this pin. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR. Interface GPS with Arduino. So out of the h12e 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. Supply encodeer 5V 2. It is mainly used in interfacing RF and infrared circuits.

HT12E Encoder IC

It encodes the 12 bit parallel data into serial for transmission through an RF transmitter. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

We should set the bits in same pattern on Encoder and Decoder IC to pair them.