This item is no longer available. Suggested replacements. UVAS sc Probe, 1 mm, with SC Controller · Get Quote. Continuous UV Results 1 – 20 of Search results for sc Amtax sc Ammonium Analyzer, mg/L NH₄-N, V, 5 m Filterprobe sc. This item is no longer available. Suggested replacements. UVAS sc Sensor, 5 mm, with SC Controller · Get Quote. Continuously protect plant treatment.

Author: Grojas Shakakinos
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Health and Food
Published (Last): 22 September 2004
Pages: 316
PDF File Size: 18.62 Mb
ePub File Size: 1.53 Mb
ISBN: 703-1-59981-790-8
Downloads: 82914
Price: Free* [*Free Regsitration Required]
Uploader: Meztikree

To print the manual completely, please, download it. Section 5 System Startup 5. Section 4 Operation 4. Drain body and clean the body and bubble trap. Installation Electrical Installation High-voltage wiring for the controller is conducted behind the high voltage DANGER The instrument must be installed barrier in the controller enclosure.

Section 2 General Information 2. System Startup Two types of verifications are offered. Restore sample flow to the instrument.


The event log stores a variety of events that occur on the devices such as configuration changes, alarms, and warning xc100. Failure to do so could result in serious injury to the operator or damage to the equipment. Index Index Numerics 90 Degree Detector Please contact the Hach Service Center serving your location. Table of Contents Add to my manuals Add. Section 4 Operation Section 4 Operation 4.

Troubleshooting Table 11 presents sensor warnings displayed in the Event Log, possible hachh, and corrective actions. Measurement Xfer Transfer 4.


Hach-Lange SC 100 User Manual

Turbidimeter Installation Information Installation 3. Table of Contents Section 5 System Startup Controller Display Features Operation 4. Maintenance Fuse Replacement The controller contains two mains fuses. Changing The Sensor Name Operation 4. The barrier must remain in place unless a by qualified technical personnel qualified installation technician is installing ahch for power, alarms, or relays.

Hach-Lange SC User Manual | 58 pages

See Replacement Parts and Accessories on page 55 for ordering information. Rinse with deionized water before calibrating. The frequency will depend on the nature and concentration of dissolved and suspended solids in the sample. Customize the outputs using the table in section 4. The display will flash on startup, when the hold outputs function has been activated, and when the filter function signal average is changed to a different value. Troubleshooting Troubleshooting Table 11 presents sensor warnings displayed in the Event Log, possible causes, and corrective actions.

Vis spectrophotometer for hach and hach lange water analysis methods 24 pages. Inadequate bubble removal from Increase the signal averaging time to a longer interval. Page 71 Index Sample Line Installation Pass the cable through conduit and a conduit hub or a strain relief fitting and an available access hole in the controller enclosure. Instrument Setup Operation 4. sv100

Page 39 Operation 4. Section 1 Specifications Specifications are subject to change without notice. Calibrate Sensor as required by regulatory agency Per agency-dictated schedule. The data logs store the measurement data at selected intervals. To ensure that the protection provided by this equipment is not impaired, do not use or install this equipment in any manner other than that specified in this manual. The turbidimeter sensor must be mounted within six feet of the controller unless an extension cable is used.


To locate the representative nearest you, send e-mail to intl hach. Section 1 Specifications Section 1 Specifications Specifications are subject to change without haach. Measured reading based on a gain of 1. Under normal use, Hach recommends replacing the lamp once a year to maintain peak performance. The incident light Method of Detection beam is composed of a tungsten filament light source with a color temperature between and K. Specifying The Displayed Language Operation 4. Page 20 Installation 3.

Hacn 11 Limited Warranty In the event that a defect is discovered during the warranty period, Hach Company agrees that, uach its option, it will repair or replace the defective product or refund the purchase price, subject to the pro-rated schedule above, sx100 original shipping and handling charges.

Index Sample Line Installation Maximum cable length is 9. Mounting The Controller Installation 3.

Printed in the U. Depends on sample Clean the sensor characteristics. Tug gently to check the connection. Problem resolution and fuse replacement should only be performed by qualified service personnel.

The passcode is factory set to sc the five digits must be followed by a space to remove the trailing asterisk. Setting Up System Security Operation 4.