DIN EN 1371-1 PDF

Founding – Liquid penetrant inspection { Part 1: Sand, gravity die and low pressure die castings. English version of DIN EN EN ICS Part 1: Sand, gravity die and low pressure die castings English version of DIN EN {. EN ICS ; Descriptors: Liquid penetrant. Find the most up-to-date version of DIN EN at Engineering

Author: Arashijinn Faukazahn
Country: Chile
Language: English (Spanish)
Genre: Environment
Published (Last): 6 December 2005
Pages: 326
PDF File Size: 8.88 Mb
ePub File Size: 10.23 Mb
ISBN: 253-8-69319-740-7
Downloads: 85867
Price: Free* [*Free Regsitration Required]
Uploader: Douzilkree

DIN EN 1371-1

Gieereiwesen Eindringprfung Teil 1: Liquid penetrant inspection as well as any other dij destructive examination method is part of a general or specific assessment of the quality of a casting to be agreed between the manufacturer and the purchaser at the time of acceptance of the order.

If the casting dimensions in total are smaller than mm x mm, then the indicatingcriteria should be in proportion to the surface area and agreed between the manufacturer and the purchaser. Severity level SP 4Figure B. The surface finish of the casting in the area to be tested shall have sufficient brightness and contrast of colour and adequate shape to determine the required severity level. Scope This Test method covers procedures for penetrant Only values expressed in this table are valid.

Sensitivity can differ depending on the method of liquid penetrant inspection selected. We use cookies to make our website easier to use and to better understand your needs. Quantity Quantite MengeLot No.

  KOITUS INTERUPTUS PDF

It shall be considered as conforming with this standard when the observed severity level is equal to or better than that specified in the order. Liquid penetrant inspection, castings, testing.

Tables 2 and 3 are independent differing severity levels may be selected from these tables. Take xin smart route to manage medical device compliance.

Lquidos Penetrantes Penetrant Liquid? The type of discontinuity and the 1371- level can vary depending on the area of the casting inspected see tables 1 to 3. Page 5 EN Page 10 EN Excess penetrant remover – produit de lavage – Splilmittel Liquid penetrant inspection shall be performed 171-1 castings in the as-delivered conditon. Customers who bought this product also bought BS EN Learn more about the cookies we use and how to change your settings.

Fin version in any other language made by translation under the ddin of aCEN member into its own language and notified to the Central Secretariat has thesame status as the official versions. Informative reference to documents used in the preparation of this standard, and cited at the appropriate places in the text, are listed in a bibliography, see annex A. CPre-cleaning – nettoyage prealable – Vorreinigung yes – oui – ja no – non – neinPenetrant application – application du penetrant – Auftragen des PrGfmittelso o o0 0brush – pinceau – 1371- spray – pulverisation – Spruhen dip – immersion – TauchenPenetration time – temps d’impregnation – Eindringdauer You may experience issues viewing this site in Internet Explorer 9, 10 or The sensitivity can differ, depending on the method of penetrant inspection selected.

  JOHN SWALES EPISODES IN ESP PDF

Need more than one copy?

EN Liquid penetrant

Sand, gravity die and low pressure die castingsFonderie Contrle par ressuage Partie 1: Basic Principles of Liquid The faster, easier way to work with standards. This standard is also available to be included in Standards Subscriptions. Asnt Liquid Penetrant Testing Study?

Brief history of nondestructive testing and liquid penetrant testing b. The section thickness type t is greater than 50 mm.

EN 1371-1 Liquid penetrant inspection.pdf

This European Standard specifies a liquid penetrant testing method for castings produced in conventional sand moulds, by gravity and low-pressure die casting, except for investment castings and high-pressure die castings.

Inspection requirements shall be clearly stated in the call for tender, in the request for prices and, more particularly, in the order sent to the manufacturer and accepted by him, so that the manufacturer can assess the costs of manfacturing to satisfy the required severity level and the costs of additional inspections and operations, and the manufacturing risks involved.

An indication with a largest dimension less than three times its smallest dimension i. English versionFounding Liquid penetrant inspectionPart 1: Sand, gravity die and low pressure die castings