Densen DM (£). “The Densen sounds excatly as it looks – big and lush. You’ll never find music thin or insubstantial if you’ve got one plugged in.”. Specifications. Power output: 75 watts per channel into 8Ω (stereo). Frequency response: 2Hz to kHz. Total harmonic distortion: %. Input sensitivity. Densen Audio DM Integrated Amplifier. Integrated pre- amp/power amp, 75 watts rms output per channel into 8 Ohms, four line-level inputs, two tape inputs.
|Published (Last):||3 February 2017|
|PDF File Size:||3.18 Mb|
|ePub File Size:||4.38 Mb|
|Price:||Free* [*Free Regsitration Required]|
Di cosa si tratta.
Therefore, good speaker cables with low capacitance should be chosen for the best performance. Their elegant sound is matched only by their looks. The presence of negative feedback has several purposes, among others: The use of a loop would require a tape monitor switch, and this would mean that the signal path has to be routed through the switch.
A red LED in between the two brass control knobs illuminates when the units are on, and slowly fades when turned off. The Alps potentiometers for volume control are marvelously smooth and noise free, allowing a very gradual increase in sound levels even in the 7 – 10 o’clock region. The Alps potentiometers for volume control are marvelously smooth and noise free, allowing a very gradual increase in sound levels even in the 7 – 10 o’clock region.
In any case, this is one of the very few amplifier designs we have ever tested that has this type of sound characteristic, and we consider it an extremely desirable one.
The tape inputs and outputs are not tape loops. Thomas Sillesen, the designer of the Densen 1, was there to answer our many questions about this unique amplifier.
A red LED in between the two brass control knobs illuminates when the units are on, and slowly fades when turned off. Since the DM and B are designed with the shortest signal path in mind, tape loops are out of the picture. In fact, the LED on the DM took 45 minutes to completely turn off since it is connected densrn the power capacitors.
We highly recommend that you audition these md components.
Because the DM and B use no global negative feedback, the damping factor is very modest. For the Dmm, there are 40, microfarads of capacitance for the input stages and the same for the output, while the B uses 10, microfarads for the input, and 30, for the output. Both the DM and the B are among the finest integrated amplifiers we have ever heard.
Densen DM10 MKII Stereo Integrated Amplifier
The thumps are due to the lack of any additional circuitry which would eliminate the thump but possibly degrade the signal. In any case, this is ddm of the very few amplifier designs we have ever tested that has this type of sound characteristic, and we consider it an extremely desirable one. They are probably the result of even order harmonic distortion – a hallmark of the SET – that do not occur to any significant degree in the Densen ddm. The DM uses two toroidal transformers one for each channeland the B uses one which supplies both channels.
In fact, the LED on the DM took 45 minutes to completely turn off since it is connected to the power capacitors. There are only two knobs on the front, one for volume control and the other for selecting the inputs. The upper portion of the audio spectrum is laid back, not quite as much as the SET, but just a little, and the mid-range is glorious, just like the SET.
Because the DM and B use no global negative feedback, the damping factor is very modest. We highly recommend that you audition these superb components. Audiocostruzioni e punto vendita di: The amplifiers are built partially by robot, and partially by hand assembly. Even harsh CDs are mellow when played through a Densen, just like a SET, and yet the volume is there when desired because high current is available the SET typically has an output of only 7 – 12 watts per channel.
They are probably the result of even order harmonic distortion – a hallmark of the SET – that do not occur to any significant degree in densej Densen amplifiers.
Densen DM 10 | The legendary Densen DM10 amplifier. This was… | Flickr
Unlike the SET, however, the bass region on the Densens is powerful and deep. There are proponents and opponents of negative feedback, regardless of its shortcomings, and Densen has chosen the design route of using no global feedback which is very difficult to do in a solid state push-pull amplifier. The sound of the DM and B is somewhat like a single ended triode tube SET amplifier, and that is a complement indeed. However, either amplifier can be used with a surround sound processor if the processor has the capability of densne the unprocessed signal through when it is turned off.
Densen DM10 MKII Stereo Integrated Amplifier | eBay
Let us know if we need to take a look at this page or fix a bug. Densen DM10 Integrato 75 watt. The basic difference between the DM and B is in dynamic range, and perhaps a bit in the detail of the upper mid-range as well as the high deensen. The tape inputs and outputs are not tape loops.