DATASHEET 74LS93 PDF

74LS93 datasheet, 74LS93 pdf, 74LS93 data sheet, datasheet, data sheet, pdf, Hitachi Semiconductor, 4-bit Binary Counters. 74LS93 datasheet, 74LS93 circuit, 74LS93 data sheet: MOTOROLA – DECADE COUNTER; DIVIDE-BY-TWELVE COUNTER; 4-BIT BINARY COUNTER. CA. ACTIVE. CDIP. J. 1. TBD. A N / A for Pkg Type. to CA. SNJ54LS90J. CA. ACTIVE. CDIP. J. 1. TBD. A

Author: Zur Moogukinos
Country: Turkey
Language: English (Spanish)
Genre: Sex
Published (Last): 19 April 2015
Pages: 98
PDF File Size: 18.76 Mb
ePub File Size: 13.46 Mb
ISBN: 597-7-22455-951-2
Downloads: 45407
Price: Free* [*Free Regsitration Required]
Uploader: Dugal

Typically 45 mW High Count Rates. Ripple cascading is also easy. Contact the seller – opens in a new window or tab and request a postage method to your location.

Products conform to specifications per the terms of Texas Instruments standard warranty. Synchronous counters are not afflicted by the obvious glitches of ripple counters, but they can still suffer from glitch problems of a more subtle nature. Test the counter by putting kHz on the clock, and you should read 1 kHz at Q G.

IC Datasheet: 74LS93

The clock cannot be regulated experiments with pulling the crystal oscillator will be madealthough its rate is constant and can be determined by observation, so that the correct time can always be found. My inexpensive wristwatch seldom is off by more than a second in several months, by comparison with WWV.

Any power supply working directly from the mains has grounding problems that are well-known. A logic high on S causes Q to go high, while a logic high on R causes Q to go low, provided E is low.

74LS93 데이터시트(PDF) – Motorola, Inc

Connect the clocks together and control them with the pushbutton. By cascading two modulo counters and a modulo counter, you now have an electronic escapement for a clock, which is fed by a 1.

  ARTRITE GOTOSA PDF

Both the load and clear for this counter are synchronoustaking effect only on the next clock edge. Therefore, the outputs should be buffered if they drive anything other than CMOS. Check this state by state to verify that it is correct.

There is nothing strange at all in this. Two counters are used, one for the tens upper nibble and one for the units lower nibble. Amazingly, it will count from 00 to datasheey, just what we want for seconds and minutes. Pulses to be counted are applied to the clock input of the 74os93 flip-flop, which toggles on every pulse. In this oscillator, the 10M resistor biases the inverter to the middle of its linear region output 2.

This power supply works very well.

74LS93 – 4 Bit Binary Counter

For this reason, it is not usual to look at the intermediate bits of a ripple counter, and they are not satisfactory for clocks. This requires a slow change at the minutes level, as well as a rapid change for large alterations. This frequency is not precisely stable in the short term, but over longer intervals, of perhaps a day, it is adjusted by speeding up or slowing down the alternators so that a clock based on it does not gain or lose time.

This refers to the intermediate states while the action is rippling down the line, which may trigger unwanted events. New other see details. Learn More – opens in a new window or tab International postage and import charges paid to Pitney Bowes Inc.

When the switch is again moved to run, the clocks will not experience an active clock edge and will not change unexpectedly.

  BUAH KERSEN PDF

7493 as a “divide-by-10 counter”

Of the 16 pins, 2 are for the power supply, datasheeh 10 for the decoded outputs representing The 74LS90 has two sections, one a modulo-2 flip-flop with clock C0 and output Datashee, and the other a modulo-5 counter of three flip-flops with clock C1 and outputs Q1, Q2 and Q3. Learn more – opens in a new window or tab. A photograph will be shown here when the film has been developed and scanned.

This shows the general principle of designing a modulo-N counter. Each of the outputs goes positive during its time interval, remaining low otherwise. The 74LS93 does not have this, and the pins are no connection. RCO then remains low until the next time 15 is reached, and so 74lss93.

Feedback is supplied by the k resistor and the crystal. It is necessary to keep the voltage supplied to the regulator above 7. The output of datashdet slave is fed back to the input of the master, but there is no possibility of a “race” because the two are never simultaneously enabled the actual circuit makes certain of this; the simple inverter, of course, shown in the diagram would not, because of propagation 74lls93. The transformer is easy to find. The output misnamed Carry Out, CO, is not a carry-out, but has a very definite purpose.

What you want is one that is normally closed one way, and springs back when pressed and released.