to meet you. If you are wondering where this is, take a look at cadstar, my “home”- page. Self Teach/ directory, then click [START]. You can . 4 PCB Design Self Teach Course. A Block Diagram Of The System. The complete CADSTAR system, including libraries, is shown below: The purpose of each. Re: CADSTAR tutorial or book. try the express tutorial on the zuken website. If you search then the self teach files are available too.

Author: Dulrajas Fenrirn
Country: Great Britain
Language: English (Spanish)
Genre: Life
Published (Last): 24 September 2016
Pages: 278
PDF File Size: 20.82 Mb
ePub File Size: 10.72 Mb
ISBN: 410-7-73696-224-4
Downloads: 16185
Price: Free* [*Free Regsitration Required]
Uploader: Jushicage

Later in this course, you will see how to restrict P. Task – to apply an attribute Also, the routing tools do not work on any invisible items; so colour settings can affect the scope of your routing.

If you draw a small box, you will frame out a lot. If Springback is enabled, but Dynamic pushing is not, components can still be pushed aside with the nudge hotkey, p, while the component is dynamic. Only the selected connection is shown together with the route segments being sel. The attribute value for the top pin will be updated in the dialog to show sef new Exit directions.

CADSTAR PCB Self Teach –

How reliable is it? They are generated by the design software and reflect such parameters as the component’s cwdstar and rotation, and the side of the board on which it is placed.

If you wish to continue using the newly installed Driver: In this task you will examine this attribute in more detail. By clicking on the ‘Configure’ button next to the list, a new dialog will appear that will enable you to edit the attributes displayed, and the order of the columns: The toolbars available are shown below, with their related shortcuts.


Use the Fix tool to hold cadstwr in their current positions. Complete the route by moving the cursor over the pin at the end of the connection. Tach significantly reduces development time and cost of complex high-speed PCBs using concurrent power integrity simulation.

If there is only a routing data file, the Routing variant is started without floorplanning capabilities. You can use this interactive push-aside technique at any time during the placement process.

Holding the CTRL key down extend the selection by clicking on several other items. Task – to set colours for net names In this way you can easily tab around the items under your cursor and select the one you require. Release the left-hand mouse button now and see the effect.

You need to enable the Allow Component Move option. Now apply your changes and close the Appearance dialog by selecting the OK button. Use the tab to display the Board level attributes.

CADSTAR tutorial or book

Select all the ten pads that should have exit directions of inwards and outwards cadshar. CMOS Technology file 1. Select an existing horizontal or vertical route segment by clicking the left hand mouse button. If the key is used more than once during a single move operation, components moved by previous pushes will try to spring back if Springback is enabled.

The value used is set from the Routing Tool Options dialog: Can I manually route curves?

This will only last for the duration of the move, or until the p key is pressed again. Register to access Zuken. Documentation Symbol Editor Is for creating graphically the non-electrical shapes and figures stored in the Documentation Symbol library. These files reside in the directory structure for the job.

Free PCB Design Software – CADSTAR Express | Zuken

Notice how an item in the design becomes highlighted with a dashed outline and the status bar changes to describe that item. The Routing variants you can choose are the Basic, or By this method, for example, you can display all the pads and tracks for the signal VDD in teacb, and all GND pads and tracks in green. You will be introduced to many of the commands during this course.


Editor XR or P. Signal names, including wildcards, can be added to the list.

Click on the Finish button You may obtain the next dialog it depends on your Operating System: For the Template and Spacing levels you are recommended to use the All display options button to show all the items.

Whole Net lets you select the whole of a net, including all branches of that net. Choose either Node Locked or Network Licensed. You can set selff to help you identify which side components are placed on.

CADSTAR Downloads

Areas With this option you can select an Area by specifying its name. The effect of the change is cadtsar on the map. Software Protection An Overview This tool is useful in situations where many components are displaced by dynamic pushing.

This specifies that there are four items under the mouse cursor, and the item that will be selected if you click the left-mouse button is a via on net GND. The exception is when the wildcard you have entered selects already selected components – these components are then de-selected. It is essential that you install the Software Key. Taech will make it easy for you to tell which item is on which layer.