D External dimensions. D Connections. D Connection of motor. FANUC CONTROL MOTOR AMPLIFIER α series DESCRIPTIONS. B–E. B–E. FANUC AC SPINDLE MOTOR α series PARAMETER MANUAL B– E. FANUC SERVO AMPLIFIER α series DESCRIPTIONS. B–E. FANUC SERVO AMPLIF IER @ series DESCRIPTIONS BE/03 The export of this product is subject to the authorization of the.
|Published (Last):||26 October 2013|
|PDF File Size:||12.31 Mb|
|ePub File Size:||18.25 Mb|
|Price:||Free* [*Free Regsitration Required]|
D The rated output of the motor is guaranteed for the rated input voltage. Take appropriate action according to the contents of the alarm. When a circuit breaker with a ground fault interrupter is used, it must be selected so that the sum of 65162d values bb according to a and b described below is not greater than the non—operating current value. For built—in motors and motors with special specifications, refer to the relevant specifications.
F Leave sufficient space around the machine to enable maintenance to be performed easily.
If a regenerative discharge unit with a resistance of 16? Magnetic Sensor for Orientation. If a screw is lost inside the nit and the power is turned on, the machine may be damaged. This causes a high—frequency leakage current to flow via the ground drift capacitance in the motor winding, power cable, and amplifier. Category Ordering number Specification For line—to—line installation: F Notes on contacting FANUC Inform FANUC of the details of an alarm and the specification code of the amplifier so that any components required for maintenance can be quickly secured, and any other necessary 6516e2 can be taken without delay.
Periodic cleaning is necessary. Daito Communication Apparatus Co. F Before operating the motor for the first time, mount and adjust the position and speed detectors.
If any clearance is left between the power magnetics cabinet and the surface on which the amplifier is mounted, dust entering the 56162e may build up 651662e prevent the normal operation of the amplifier. Recommended noise filters are given in 12 of Section 2. Check that the delivered amplifier is as originally ordered. Separation of Signal Lines. V Never ground or short—circuit either the power supply lines or power lines.
F Mount a ground fault interrupter.
D Basic insulation is used on the protective ground side. This carries away the heat generated by the semi— conductors, thus preventing heat from building up in the cabinet as much 56162e possible.
When the rated output capacity is 11 kW or less, calculate the maximum output capacity according to 3. If the amplifier is used continuously with an excessive load applied, the amplifier may be damaged.
Fanuc Servo Amplifier Alpha Series Descriptions 65162E
Take appropriate corrective action, then resume operation. Selecting a Noise Filter. The table below lists the signal types.
Protection Against Electric Shock. Check the interface with the CNC being used, then select an appropriate servo amplifier module.
A loose screw, loose connection, or the like will cause a motor malfunction or overheating, or a ground fault. Rated output capacity of a power supply module y 30— minute rated output of a spindle motor For the rated output capacities of the power supply modules, see Table 4.
For combinations of servo motors and servo amplifier modules, see Sections 3. If the work to be done requires that the door of the power magnetics cabinet be left open, the work must be carried out by a person trained in the maintenance of the machine or equipment.
Fanuc Servo Amplifier Alpha Series Descriptions E pdf – CNC Manual
Therefore, the PSM is selected as follows: Configuration and Order Drawing Number. For those modifications, see Section 8. Spindle switching control switching the speed only, or switching both the speed and position 2.
For the connector dimensions, see Appendix D. Motor speed at rapid traverse [min—1] D: Also, do not stack unpacked amplifiers on top of each other. Otherwise, the cooling efficiency will be reduced so that the characteristics of the amplifier cannot be guaranteed.
Fanuc B-65162 Manuals
F Tighten all screws firmly. When the fan adaptor is installed, the panel cut—out must be partially modified. The cables that run into the amplifier and which require shield processing, with the exception of K14, K15, 65162, K18, K19, K31, and K33, must be clamped as indicated in Fig. Clamping secures a cable and also provides shielding.
Do not place anything on the amplifier. Select a power supply module with a 56162e output not less than the sum of the total continuous rated output of the spindle motors times 1.
Connect the other ground terminal of the terminal block to the frame ground. Use a regenerative discharge unit of a suitable capacity for the load and operation cycle time.
D The primary power supply and main circuit and the secondary control circuit are separated from each other by reinforced insulation. Never touch them directly. As indicated in the table below. This is because the capacitor unit for power—factor improvement may adversely affect power regeneration. Then, select an appropriate spindle amplifier module for the selected spindle motor. From motor power cable M5 screw??? Read the Warning, Caution, and Note thoroughly before attempting to use the 65162w.