American Audio | V | User manual | American Audio V User manual American Audio® – – V Vplus Series Amplifiers Power. American audio V PLUS Pdf User Manuals. View online or download American audio V PLUS User Instructions. View and Download American Audio V/V user instructions online. PROFESSIONAL POWER AMPLIFIERS. V/V Amplifier pdf manual.

Author: Shaktile Jujas
Country: Anguilla
Language: English (Spanish)
Genre: History
Published (Last): 21 June 2008
Pages: 120
PDF File Size: 1.14 Mb
ePub File Size: 12.86 Mb
ISBN: 743-5-73116-665-2
Downloads: 23071
Price: Free* [*Free Regsitration Required]
Uploader: Akinozahn

The dip switches on the rear panel ameican you to configure the low cut filter. This fans are used to cool the internal parts of the amplifier when in use.

Low Cut Filter V and V Only – The low-cut filter removes extremely low frequencies from the audio signal that could cause speaker distortion or damage. Typical speaker output f3000 bare wire.

American Audio V PLUS Manuals

Before using this amplifier, read the user manual for further warnings. Connecting to the wrong voltage is dangerous and may damage the amplifier. Table Of Contents ser- vicing instructions in the user manual accompanying the CD player.

Be sure that supplied voltage matches that of the required voltage of you amplifier. During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and ausio inaudible.

A limiter takes the gain of an overloading signal and reduces it, the reduction in gain reduces distortion that can cause damage to your speakers and amplifier. It’s a community-based project which helps to repair anything. Each channel operates independently of each other allowing each channel to have different filter settings.

Configuring the Low Cut Filter: You may also visit us on the web at www. Mono bridge operation connections will follow the above descriptions however, when operating americaj mono bridge audlo the speaker connections will run between the two positive red leads.


Amplifiers are shipped in stereo mode. See page 9 for more details on input configuration.

Objects have fallen, or liquid has been spilled into the unit. Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response. If the input gain level is not reduced the built-in limiter will activate.

These fans are used to cool the internal parts of the amplifier. A short circuit will usually be traced to a bad cable or a bad speaker and is rarely traced to the amplifier itself.

Cooling Fan – Dual speed cooling fans.

American Audio V3000/V2000 User Instructions

Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into Diagram 8 the red terminal. During signal overload, the limiter will reduce the input audio signal enough to minimize the amount of clipping. Connect a XLR cable to the input of channel one. Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable.

Insert bare wire into the binding post and tighten. Rear mounting the unit is especially recommended if the unit is to mounted into a mobile rack. A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself.

Channel 1 Gain Control – This rotary knob is used to control the output signal of channel one. Fuse Holder – 10 5 11 6 12 1 Diagram 3 This holder houses the external fuse. American audio professional power amplifier user instructions vlp series 18 pages. Ground Lift Switch – This switch is used to disconnect the internal ground signal from the amplifier chassis ground.


This is to protect any speakers connected to the channel. In the event of an electrical overload the breaker will pop-out.

Service Hours are Monday through Friday 9: Connect your speaker across the red output binding post on the rear of your amplifier. To reduce the risk of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with that of another.


This symbol is intended to alert the user of the presence of important operating and maintenance servicing instructions in the literature accompanying the product. Fuse Holder – This holder houses the external fuse.

The amplifier can operate at practically any power level without risk of overheating.

This manual also for: Risiko – Elektrischer Schlag! Channel 1 Frequency Adjustment. Antes de usar este amplificador, lea mas advertencias en la guia de operacion. Never block the fan in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail.