2SC1307 DATASHEET PDF

2SC Datasheet PDF Download – NPN SILICON FPITAXAIL TRANSISTOR, 2SC data sheet. Description, NPN Silicon Fpitaxail Transistor. Company, ETC. Datasheet, Download 2SC datasheet. Cross ref. Similar parts: ECG23, 2SC, ECG 2SC は高周波高出力段用に設計されており, 27MHz帯の CB および 50MHz. * C – 7 BRISLIT. GEOT DAMEMO,. 短絡に対する耐破壊強度が大です。.

Author: Voodoozilkree Sasida
Country: Iran
Language: English (Spanish)
Genre: Photos
Published (Last): 1 December 2006
Pages: 461
PDF File Size: 16.82 Mb
ePub File Size: 3.58 Mb
ISBN: 330-9-63308-482-4
Downloads: 31156
Price: Free* [*Free Regsitration Required]
Uploader: Vujas

The amplifier terminates broadband style toroid transformer putting its rf energy into a diode ring mixer which by definition is a balanced mixer circuit.

But it was a hard way to go there!

Datasheets search archive of electronic components datasheets

Due to the fact that my rig needs 3 sections of relay switched circuitry rx front end, band filter past the tx mixer and low pass filter past the exciter I switched the corresponding relays for one band in series. So fakers will make their profit by selling counterfeits of these parts. Building a multi band rig is, as you might conceive, much more complicated than setting up a monobander.

Adequate emitter bypassing was one of these. The transmitter I have to admit, I underestimated the diffculties that I was going to face when constructing a 3 to 30 MHz broadband QRP amplifier with a power output level of about 10 watts on all the five bands covered. There are three sections in which band switching must take place in my rig: I will talk about this in a later post. I had two cases of faked semiconductors the recent year. Please note that you need a preamplfier if you run that mixer type by a DDS because the outputlevel of a DDS if not amplified does not suffice the 7 dbm a diode ring mixer needs for proper operation.

First I used large capacitors in the range of 0. Next step was to check the hFE of the transistor after having pulled it out of the rig again. Frequency calculations For the two lower bands 80 and 40 meters the operating frequency is calculated by the following scheme: But, as a passionate homebrewer, I thought to myself: The AD is capable of being clocked with MHz maximum rate.

  HPING MANUAL PDF

All what you have got to do is to connect the various ports of the microcontroller to your application.

That said, I was wrapping up my NorCal 40A 40M rig, plugged both into the board, and obtained similar results. For example computer crystals of 9, kHz, standard 9, kHz xtals or others in the same frequency region can be used.

The design is capable of delivering about 20 watts of rf power but I wanted to run it within a well defined distance from its limits to ensure top signal quality. Each time I get a new package of RF power transistors today, the first step is to check them out in the former CB rig if they are able to deliver the desired output power.

See the full scheme for this one! They hereby can serve as impedance transformers, because input impedances of trasistor stages are often in the range of only some ohms whereas the output impedances of the previous stages are 4 to 10 times higher.

For the two lower bands 80 and 40 meters the operating frequency is calculated by the following scheme:. Most of them do honest business but some are black sheep that sell counterfeits of mainly semiconductors.

But other crystal frequencies are also possible. Emitter degeneration in a transistor amplifier stage The unbypassed capacitors causes a voltage drop when emitter-collector current rises.

In the middle of the sandwich you can recognize the switching unit from datasheeh the plugs are lead to the receiver and transmitter board. Go to a US or European based seller. I read a lot of stuff in advance, particularly the ARRL library, to get aquainted with 2c1307 basics of designing linear broadband amplifiers for rf. Here is the description of this optimized DDS vfo.

If available check the output with a spectrum analyzer! This cannot be undone. A spreadsheet software is extremely useful for this purpose, because you can change the IF quickly and see at first glance what you will get out when the DDS is about to generate the needed frequency to bring you to the 2sc13007 band.

  GUNAWAN WIRADI PDF

The upper part where the device is mounted to the heatsink does not look the same.

NEC 2SC To NPN Silicon Fpitaxail Transistor | eBay

Thank you very much, Harold and Ollie. No intermodulation or other interference by strong broadcasters close to ham bands particularly on 40 meters! Must be able to seperate strong out of band signals broadcaster etc.

I put 12 V DC to it with wrong polarity. It worked from the start. DDS controlled by microcontroller Colored graphic LCD 5 ham bands 80, 40, 20, 15 and 10 2scc1307 to be covered SSB only 10 Watts out, transmitter equipped with bipolar transistors in push-pull mode lots of CB-types still on my stock or replaced e.

The price for 6 pieces was abt. Several voltage dividers are visible on the upper left part of the scheme. One of the reasons for this was improper shielding of the band filter section that follows the TX mixer. They are more or less crap. And, because a push-pull amp offers built-in even-harmonics suppression, the production of overtones is limited by this circuit without the need for filters.

Other manufacturer searches related to 2SC1307

For further buyings of RF power transistors. Again this is to avoid the repeated soldering process ruining my Veroboards: These boards are equipped with an ATMega datashset which is capable to deliver enough capacity and calculation power even for extended software. Got an idea why? All lines are connected by the side-plugs. The waveform of the two-tone test is absolutely top on all the 5 bands.